Prevista Dry frame element
Product information
Prevista Dry frame element
for Prevista Dry Plus fitting holder and module
| Year built (from): | 01.03.2019. |
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Drywall builders
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Product description
Overview
- 1 Prevista Dry frame element
- 2 Screws for fixing
- 3 quick-release clamp
- 4 Slot nuts
Handling
Assembly information
Installation dimensions
Assembly
Mounting the element
Mounting to a masonry wall
-
Determine and mark the fixing points.
X2: 460 mm
-
Drill the holes.
-
Insert the dowels.
-
Determine and mark the fixing points on the floor.
X3: 375 mm
-
Drill the holes.
-
Insert the dowels.
-
INFO!
Mount the Prevista Dry fixing set pursuant to the instructions for use for the fixing set.
-
Loosen the feet of the element using a fork spanner.
-
Adjust the construction height of the element in accordance with the on-site marking of the upper edge of the finished floor.
X: 1000 mm
-
Tighten the feet of the element using a fork spanner.
-
The element is attached to the wall.
Mounting in Prevista Dry Plus
INFO!
Mount the Prevista Dry Plus pre-wall construction pursuant to the instructions for use of the Prevista Dry Plus system.
-
Position the element on the floor rail.
-
Fix the feet on the floor rail using the clips.
-
Set the height of the element by means of the feet.
-
Fix the element with the Prevista Dry Plus rail connectors.
-
The element is fixed in the Prevista Dry Plus pre-wall construction.
Mounting in steel stud frame
-
Position the element on the floor rail.
-
If necessary, adjust the foot depth from 50 mm (pre-mounted) to 75 mm.
-
Pull the foot out and turn by 90°.
-
Fix the feet.
-
Adjust the construction height of the element in accordance with the on-site marking of the upper edge of the finished floor.
X: 1000 mm
-
Attach the element to the stud frame using the screws supplied.
-
If applicable, connect further elements to the element via the stud frame.
Install the fitting holder
-
Open the lever of the quick-release clamp.
-
Turn the lever of the quick-release clamp 90° anti-clockwise.
-
Insert the quick release clamp through the fitting holder and into the element.
-
Turn the lever of the quick-release clamp 90° clockwise.
-
Close the lever of the quick-release clamp.
-
Repeat these steps on the other side.
-
The fitting holder is fastened in the element.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.