Multiplex Trio E extension set
Product information
Multiplex Trio E extension set
for all control elements, concealed, cavity wall
Trade mark rights exist for this document; for further information, go to viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Operators
Consumers
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
INFO!
This symbol gives additional information and hints.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Intended use
The extension set is suitable for modifying the following elements for a pre-wall, a masonry wall or outside the shower tray edge:
Multiplex Trio E2 bath mixing unit model 6146.2
Multiplex Trio E3 bath mixing unit model 6146.215
Multiplex Trio E bath mixing unit model 6146
Product description
Overview
- 1 Conduit pipe
- 2 Sealing collar
- 3 Seal plug
- 4 Cover rosette
- 5 Connection socket
- 6 Fixing screws
Handling
Assembly
Mounting the display element
Mounting the connection socket on pre-walls
-
Use a compass saw (Ø 68 mm) to saw the hole into the wall.
-
Insert the empty conduit such that two rings can be seen on the inside.
NOTICE!Do not bend the empty conduit.
-
Insert the connection socket with the word "TOP" and the outlet facing upwards.
-
Screw on the connection socket.
-
Push on the sealing collar and incorporate it into the sealing concept.
-
Insert the seal plug.
-
Tile in the connection socket.
Mounting the connection socket on masonry walls
-
Insert the empty conduit such that two rings can be seen on the inside.
NOTICE!Do not bend the empty conduit.
-
Insert the connection socket into the recess.
-
Fix the connection socket with quick-setting mortar.
-
Push on the sealing collar and incorporate it into the sealing concept.
-
Fit the seal plug.
-
Tile in the connection socket.
Mounting the display element
-
Cut off or saw off the connection socket so that it is flush with the surface.
-
Cut-off condition.
-
Insert the seal into the cover rosette.
INFO!Insert the seal so that the ends form an opening in the bottom section of the cover rosette.
-
Place the cover rosette on the flush-mounting box. Make sure that the open side of the cover rosette is located top left.
-
Select the appropriate screw length.
-
Fasten the cover rosette using the selected screws.
-
Pull the rotating knob off of the control element.
-
Loosen the screws on the control element and pull the cable out through the fastening element.
-
Insert the cable and push it through the empty conduit.
-
Insert the control element.
-
Fasten the control element to the cover rosette with screws.
-
Insert the rotating knob.
-
Put on the site protection of the rotating knob.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.